Manufacturer
HP
Model Number
C4576A
Description
Deskjet 855cxi
Interactive Exploded View
Parts List
| Part Number | Description |
|---|---|
|
|
35CC SYRINGE - FOR USE WITH CARRIAGE SLIDER ROD LUBRICANT |
|
|
ACCESS DOOR - LIFT-UP LID FOR CARTRIDGE/CARRIAGE ACCESS |
|
|
ADVANCED GLOSSY PHOTO PAPER - A SIZE (8.5 X 11-INCHES) - 25 SHEETS |
|
|
ANTISTATIC BRUSH |
|
|
ASP (AUTHORIZED SERVICE PROVIDER) TRAINING KIT FOR DESKJET 800 FAMILY PRINTERS - |
|
|
BASE ASSEMBLY - BOTTOM OF PRINTER - INCLUDES RUBBER FEET |
|
|
BELT ATTACHMENT - ANCHORS DRIVE BELT TO CARRIAGE |
|
|
BLACK PRINT CARTRIDGE (ECONOMY) - PRINTS APPROXIMATELY 415 PAGES BASED ON 5% DEN |
|
|
BLACK PRINT CARTRIDGE (ECONOMY) - PRINTS APPROXIMATELY 415 PAGES BASED ON 5% DEN |
|
|
BLACK PRINT CARTRIDGE (HIGH CAPACITY) - PRINTS APPROXIMATELY 840 PAGES BASED ON |
|
|
BLACK PRINT CARTRIDGES (HIGH CAPACITY) - (TWO-PACK OF 51645A) EACH PRINTS APPROX |
|
|
BLOTTER (ABSORBER) ASSEMBLY - INCLUDES FRAME AND BLOTTER PADS |
|
|
BRIGHT WHITE INKJET PAPER - A SIZE (8.5 X 11-INCHES) - 200 SHEETS PER PACKAGE |
|
|
BRIGHT WHITE INKJET PAPER - A SIZE (8.5 X 11-INCHES) - 250 SHEETS |
|
|
BRIGHT WHITE INKJET PAPER - A SIZE (8.5 X 11-INCHES) - 500 SHEETS |
|
|
BRIGHT WHITE INKJET PAPER - A4 SIZE (21.0CM X 29.7CM) - 500 SHEETS |
|
|
BROCHURE AND FLYER PAPER - GLOSSY ON BOTH SIDES - A SIZE (8.5 X 11-INCHES), 98 B |
|
|
CARRIAGE ASSEMBLY FLEX CABLE - OVERALL LENGTH IS 46.7CM (18.4IN) |
|
|
CARRIAGE BELT IDLER WHEEL ASSEMBLY - INCLUDES: IDLER MOUNT, PULLEY, BALL BEARING |
|
|
CARRIAGE FLEX CLAMP - HOUSES THE FLEX CABLE PRELOADER CLAMP - HOLDS CARRIAGE PRE |
|
|
CARRIAGE PCA - CONTROLS MOVEMENT OF CARRIAGE ASSEMBLY - DOES NOT INCLUDE FLEX CA |
|
|
CARRIAGE PLATE ASSEMBLY - INCLUDES CARRIAGE PLATE, PIVOT STOP ADJUSTER, AND Z AX |
|
|
CARRIAGE PRE-LOADER - HOLDS THE CARRIAGE AGAINST THE CARRIAGE ROD |
|
|
CARRIAGE RESTRAINT - PROTECTS BOTTOM OF CARRIAGE ASSEMBLY DURING SHIPMENT |
|
|
CARRIAGE ROD - SHAFT THAT THE CARRIAGE ASSEMBLY RIDES ON |
|
|
CARRIAGE ROD LUBRICATION WASHER (FELT) |
|
|
CARRIAGE ROD SPRING |
|
|
CENTER LIFTER CAP - HOLDS THE PRESSURE PLATE LIFTER AND THE KICKER SPRING IN PLA |
|
|
CHASSIS CLAMP - RETAINS CHASSIS IN THE BASE ASSEMBLY |
|
|
CHIMNEY WALL - WALL SUPPORT OF SPITTOON |
|
|
CLAMP SPRING - PROVIDES TENSION FOR THE INK CARTRIDGE LOCKING CLAMPS |
|
|
DESKJET 850C/855C MANUAL KIT (US ENGLISH) - INCLUDES USER'S, SETTING UP, CREATIN |
|
|
DESKJET AND DESKWRITER SERVICE MANUAL ON CD-ROM - VERSION 4.1 |
|
|
DOOR ACTUATOR - ACTUATES ACCESS DOOR OPEN SWITCH |
|
|
ECCENTRIC BUSHING - USED TO ADJUST PEN-TO-PAPER SPACING (2 USED) |
|
|
ENCODER SPRING - PROVIDES TENSION FOR THE ENCODER STRIP AND GROUNDS THE CARRIAGE |
|
|
ENCODER STIFFENER - PREVENTS OSCILLATION OF ENCODER STRIP |
|
|
END CAP KIT (LEFT/RIGHT) - PROTECTS PRINTER DURING SHIPPING |
|
|
FAN ASSEMBLY |
|
|
FERRITE ASSEMBLY - INSTALLED ON FLEX CABLE ASSEMBLY |
|
|
FOAM CATCH PAD - KEEPS PAPER CATCH FROM MOVING INADVERTENTLY |
|
|
FORM FEED ACTUATOR - FORM FEED BUTTON/ARM FROM FRONT PANEL |
|
|
FRICTION CORK - INSTALLED UNDER PAPER WIDTH ADJUSTER |
|
|
GREETING CARD PAPER PACK (WHITE) - A SIZE (8.5 X 11-INCHES) - INCLUDES 20 SHEETS |
|
|
GREETING CARD PAPER PACK (WHITE, MATTE) - A4 SIZE (21.0CM X 29.7CM) - INCLUDES 2 |
|
|
GROUND PLANE - GROUNDS POWER SUPPLY AND LOGIC PCA |
|
|
HP 45 ECONOMY BLACK INKJET PRINT CARTRIDGE - PRINTS APPROXIMATELY 415 PAGES BASE |
|
|
HP INK CRTG 41A COLOR AP |
|
|
HP INK CRTG 41A COLOR CAN |
|
|
HP INK CRTG 41A COLOR EUR |
|
|
HP INK CRTG 41A COLOR LAR |
|
|
HP INK CRTG 41A COLOR NAM |
|
|
HP INKJET CRTG 45A BLACK LARGE CAN |
|
|
HP PRINTERPAL ACCESSORY - ADDS (EXTERNAL) FAX CAPABILITIES TO THE LASERJET PRINT |
|
|
HP SCITEX LATEX PRINTHEAD RETURN KIT |
|
|
HP TEXTURED HALF-FOLD GREETING CARDS (WHITE) - A SIZE (8.5 X 11-INCHES) |
|
|
I/O CAP - LEFT SIDE |
|
|
I/O CAP - RIGHT SIDE |
|
|
I/O DECK - HOLDS WINGS AND SINGLE SHEET WIDTH ADJUSTER |
|
|
I/O TRAY BASE - HOLDS THE PAPER, PRESSURE PLATE, WIDTH ADJUSTER AND PAPER CATCH |
|
|
INKJET NON-GLOSSY LX PAPER - A4 SIZE (21.0CM X 29.7CM) - 200 SHEETS |
|
|
INTERFACE CABLE KIT - FOR HP PERIPHERALS DESIGNED FOR USE IN AN APPLETALK/PHONEN |
|
|
IRON-ON T-SHIRT TRANSFERS - A SIZE (8.5 X 11-INCHES) - 10 SHEETS |
|
|
IRON-ON T-SHIRT TRANSFERS - A4 SIZE (21.0CM X 29.7CM) - 10 SHEETS |
|
|
KEYPAD BEZEL - COVERS THE KEYPAD - ATTACHES TO THE FRONT RIGHT OF THE TOP COVER |
|
|
KICKER - RESTACKS THE PAPER IN THE PAPER INPUT TRAY AFTER THE TOP SHEET IS REMOV |
|
|
KICKER SPRING - PROVIDES TENSION FOR THE KICKER |
|
|
LATCH SPRING - PROVIDES TENSION FOR TRAY LATCH |
|
|
LEFT LIFTER CAP - HOLDS THE PRESSURE PLATE LIFTER IN PLACE |
|
|
LEFT PIVOT CLAMP (LEFT Z-STOP) - HOLDS THE LEFT END OF THE PIVOT ASSEMBLY IN PLA |
|
|
LEVER ARM SPRING - PROVIDES TENSION BETWEEN THE LEVER ARM AND THE PRESSURE PLATE |
|
|
LIGHT PIPE ASSEMBLY - TRANSFERS LIGHT FROM LED TO KEYPAD - LIGHT PIPE WITH POWER |
|
|
LOWER PAPER GUIDE |
|
|
MOTOR CABLE ASSEMBLY WITH FERRITE - A 14-PIN (F) CONNECTOR TO A 2-PIN (F) CONNEC |
|
|
NAMEPLATE - C4576A DESKJET 855CXI PRINTER LOGO |
|
|
O-RING - NITRILE RUBBER, 6MM ID, 2MM DIAMETER CROSS-SECTION, 70 DUROMETER |
|
|
OOPS FLAG - OUT OF PAPER SENSOR |
|
|
PAPER ACCESS COVER ASSEMBLY - LIFT-UP TOP/FRONT COVER |
|
|
PAPER CATCH SPRING - PROVIDES TENSION FOR LENGTH ADJUSTMENT |
|
|
PAPER MOTOR GROUND STRAP |
|
|
PHOTO GREETING CARDS (WHITE, MATTE) - A SIZE (8.5 X 11-INCHES), HALF FOLD, PRE-S |
|
|
PHOTO QUALITY INKJET PAPER (MATTE) - WITH TWO SIDED MATTE FINISH - A SIZE (8.5 X |
|
|
PIVOT SPRING - PROVIDES TENSION FOR THE PIVOT |
|
|
PIVOT STOP ADJUSTER - INSTALLED NEAR LEFT END OF CARRIAGE PLATE |
|
|
POWER CABLE - HAS TWO 9-PIN (F) CONNECTORS - 3.4CM (1.3IN) LONG |
|
|
POWER CORD (FLINT GRAY) - 17 AWG, 2.3M (7.5FT) LONG - HAS 90 DEGREE (F) C13 RECE |
|
|
POWER CORD (FLINT GRAY) - 17 AWG, 2.3M (7.5FT) LONG - HAS 90 DEGREE (F) RECEPTAC |
|
|
POWER CORD (FLINT GRAY) - 2.3M (7.5FT) LONG - HAS 90 DEGREE (F) RECEPTACLE (FOR |
|
|
POWER SUPPLY ASSEMBLY |
|
|
POWER SUPPLY COVER - SHIELDS AND PROTECTS POWER SUPPLY PC BOARD |
|
|
POWER SUPPLY INSULATOR - INSULATES POWER SUPPLY FROM CHASSIS |
|
|
PRE-GUIDE (FOR ENVELOPES) |
|
|
PREMIUM GLOSSY INKJET PAPER - A SIZE (8.5 X 11-INCHES) - 10 SHEETS |
|
|
PREMIUM GLOSSY INKJET PAPER - A4 SIZE (21.0CM X 29.7CM) - 10 SHEETS |
|
|
PREMIUM GLOSSY PAPER - A SIZE (8.5 X 11-INCHES) - 25 SHEETS PER PACKAGE |
|
|
PREMIUM HIGH-GLOSS FILM - A SIZE (8.5 X 11-INCHES) - 50 SHEETS |
|
|
PREMIUM HIGH-GLOSS FILM - A4 SIZE (21.0CM X 29.7CM) - 50 SHEETS |
|
|
PREMIUM INKJET HEAVYWEIGHT PAPER - A4 SIZE (21.0CM X 29.7CM) - COATED ON BOTH SI |
|
|
PREMIUM INKJET RAPID-DRY TRANPARENCIES - A SIZE (8.5 X 11-INCHES) - 50 SHEETS |
|
|
PREMIUM INKJET RAPID-DRY TRANPARENCIES - A4 SIZE (21.0CM X 29.7CM) - 50 SHEETS |
|
|
PREMIUM INKJET TRANSPARENCY FILM - A SIZE (8.5 X 11-INCHES) - 20 SHEETS |
|
|
PREMIUM INKJET TRANSPARENCY FILM - A SIZE (8.5 X 11-INCHES) - 50 SHEETS |
|
|
PREMIUM INKJET TRANSPARENCY FILM - A4 SIZE (21.0CM X 29.7CM) - 20 SHEETS |
|
|
PREMIUM PHOTO PAPER (GLOSSY) - A SIZE (8.5 X 11-INCHES) - 15 SHEETS |
|
|
PREMIUM PHOTO PAPER (GLOSSY) - A SIZE (8.5 X 11-INCHES) - 50 SHEETS |
|
|
PRESSURE PLATE ASSEMBLY - LIFTS PAPER STACK TO BE PRINTED |
|
|
PRESSURE PLATE LIFTER - ALSO KNOWN AS LIFTER SHAFT OR PAPER LIFTER |
|
|
PROFESSIONAL BROCHURE AND FLYER PAPER (MATTE) - A SIZE (8.5 X 11-INCHES) - 50 SH |
|
|
RETURN KIT - FOR RETURNING DEFECTIVE THERMAL INKJET (TIJ) 2.5 CARTRIDGES - INCLU |
|
|
RIGHT PIVOT CLAMP (RIGHT Z-STOP) - HOLDS THE RIGHT END OF THE PIVOT ASSEMBLY IN |
|
|
RIGHT WING - HOLDS PRINTED PAPER AFTER BEING EJECTED |
|
|
ROUND RE-STICKABLE INKJET STICKERS - HP BRIGHT WHITE 6.35CM (2.5IN) ROUND STICKE |
|
|
RUBBER FOOT - REPLACEMENT RUBBER FOOT FOR THE BOTTOM OF THE PRINTER (TWO USED) |
|
|
SEPARATOR LIFTER |
|
|
SEPARATOR LINK (SEPARATOR PEG) |
|
|
SEPARATOR SPRING - PROVIDES PRESSURE BETWEEN THE SEPARATOR ASSEMBLY AND THE CENT |
|
|
SERVICE STATION MOTOR |
|
|
SERVICE STATION TUMBLER ASSEMBLY |
|
|
SIDE COVER - SERVICE STATION ACCESS DOOR |
|
|
SPECIAL LUBRICATING OIL - FOR CARRIAGE SLIDER ROD SURFACE - 1 QUART BOTTLE (.95 |
|
|
SPITTOON ASSEMBLY - FRAMEWORK OF TUMBLER ASSEMBLY |
|
|
SQUARE RE-STICKABLE INKJET STICKERS - HP BRIGHT WHITE 6.35CM (2.5IN) SQUARE STIC |
|
|
TOP COVER - DOES NOT INCLUDE CARRIAGE ACCESS DOOR |
|
|
TOP COVER BRACKET - INSTALLED BETWEEN OLD STYLE GROUND PLANE AND TOP COVER |
|
|
TRAY LATCH - HOLDS PAPER TRAY IN PLACE |
|
|
TURNAROUND ASSEMBLY - HOLDS BELT TENSION COMPONENTS IN PLACE |
|
|
WASHER RETAINER - HOLDS CARRIAGE ROD LUBRICATION WASHERS IN PLACE |
|
|
WIDTH ADJUSTER - PAPER STACK WIDTH ADJUSTER |
|
|
WIDTH SPRING - PROVIDES FRICTION FOR PAPER WIDTH ADJUSTER |
|
|
WING HOLDER - SUPPORTS OUTPUT TRAY WINGS DURING SHIPMENT |
|
|
Z AXIS SERVICE STATION ADJUSTMENT (ZASSA) |